ACCESSING THE MT02 MULTI-TOOL

ALWAYS USE THE PULL TAB WHEN ENGAGING & DISENGAGING THE MT02 MULTI-TOOL

Lift up on the pull tab as you keep steady the wallet frame to access the MT02 Multi-Tool.

Lift up on the pull tab as you keep steady the wallet frame to access the MT02 Multi-Tool.

THE MT02 MULTI-TOOL HAS 3 LOCK POINTS WHICH ENABLES MULTIPLE GRIP POSITIONS.

THE MT02 MULTI-TOOL HAS 3 LOCK POINTS WHICH ENABLES MULTIPLE GRIP POSITIONS.


ANATOMY OF THE MT02 MULTI-TOOL

Untitled-1-03.png

A.     Para-cord Tensioner & Safety Pull Tab
B.     Sharp & Serrated Knife/Can Opener
C.     1/4” Hex Wrench
D.     Lock Notch Tabs (3 positions)
E.     Grip Handle
F.     2.5” Ruler
G.     15mm Hex Wrench + Phone Stand 1
H.     Secure Strap
I.     Bottle Opener, Nail Pryer & Flat Head
J.     10mm Hex Wrench & Phone Stand 2

REMOVE MULTI-TOOL BEFORE FLIGHT


REMOVING THE SILICONE BAND

The secure strap forks help keep the silicone band in place. The diagram points out the names of these parts

1. Remove all contents of the wallet including the back plate as well as the MT02 Mulit-Tool if applicable.

2. Adjust the silicone band until the the thicker portion of the band is past the secure strap. This allows us to disengage the band on the thinner portion of the band where there’s less tension & more elasticity.

3. Starting on the secure strap wide side, keep the frame steady, upright and between both hands, stretch and slide the band up and over the top fork. DO NOT SLIDE OVER THE BOTTOM FORK.

4. Repeat actions on the secure strap narrow side.

Untitled-1-08.jpg

INSTALLING THE SILICONE BAND

1. Remove all contents of the wallet including the back plate as well as the MT02 Mulit-Tool if applicable.

2. Starting on the secure strap narrow side, slide the thinner portion of the band down into the secure strap. Keeping the frame steady, upright and between both hands, stretch & slide the remainder of the band down over the top fork.

3. Stretch the opposite side of the band up and over the frame and into the secure strap wide side. DO NOT SLIDE OVER THE BOTTOM FORK.

4. Adjust the silicone band to the desired position.


CHANGING THE LEATHER POCKETS

YOU WILL NEED A .050” HEX WRENCH


REMOVING THE LEATHER POCKETS
1. Remove all contents of the wallet including the back plate, the wallet band, as well as the MT02 Mulit-Tool if applicable.

2. Lay the wallet down on a flat surface and loosen all the screws completely until the leather & the screws are detached from the metal chassis.


INSTALLING THE LEATHER POCKETS
1. Remove all contents of the wallet including the back plate, the wallet band, as well as the MT02 Mulit-Tool if applicable.

2. Insert all the screws into the designated holes on the leather pockets, making sure they are fully penetrated through the hole and there is nothing in the way of the screws. If the holes on the leather is too tight for the screws to penetrate, use a larger hex size to stretch out the hole before squeezing the screw through.

3. Place the leather (with the screws already in them) onto the aluminum chassis and screw them in one by one. The screws should cinch the leather down. DO NOT OVER TIGHTEN THE SCREWS NOTE: Make sure the screws are aligned & vertical to the walletto prevent the screws from stripping the threads on the chassis. Wiggle the screws around with your hex tool & you will feel it drop into place. 


SETTING UP YOUR WALLET WITH CONTENT

DANGO WALLETS ARE SLIM WALLETS AND DESIGNED TO REDUCE CONTENT,
BUT IS NOT LIMITED TO EACH INDIVIDUAL’S PREFERENCES

1. Start by designating 2 to 3 most important cards to the front leather pockets. Usually a form of ID like a drivers license or a student body card and a payment card like an ATM card or a credit card.

2. Then on the backside, spread the back cavity by utilizing the back plate’s tab to stretch the band and insert some cards. The back plate should be above all the cards. MAKE SURE ALL CARDS LAY ON TOP OF THE MT02 MULTI-TOOL IF APPLICABLE & BELOW THE BACK PLATE.

3. The wallet setup will result in a slim and tight unit that is tailored to how you would like to use it. Other ways include an ID and a Debit Card in front, and 20 business cards in the back, acting as a business card holder.